lead forensics image

BY TYPE

Diaphragm Pumps Centrifugal Pumps Peristaltic Pumps Progressive Cavity Flexible Impeller ATEX Pumps Gear Pumps Diesel-Driven Pumps Magnetic Drive Pumps Lobe Pumps Twin Screw Pumps Water Booster Sets Drum Pumps Mobile Solutions Pump Accessories

BY APPLICATION

Chemical Cosmetics & Personal Care Food & Beverage Hygienic Industrial Oil & Gas Pharmaceutical Pulp & Paper Shear Sensitive Surface Treatment Wastewater Dewatering Wellpointing

BY BRAND

BBA Pumps Logo Liverani Logo Nova Rotors Logo Pomac Pumps Logo Jessburger Logo Tapflo UK logo

SYSTEMS

Process Engineering & Design CIP Systems SLES Mixing & Dilution Unit Drum Unloading Industrial Mixers Liquid Blending System Filling Machines IBC Unloader

EQUIPMENT

Heat Exchangers Process Valves Stainless Steel Tanks

RESOURCES

Case Studies Blog Downloads

CPC Sanitary Centrifugal Pump Troubleshooting

  1. 1. CPC Pump
  2. 2. Malfunctions
Last updated 24/06/2026 3 minutes read

Having trouble with your CPC Sanitary Centrifugal Pump? Our comprehensive guide will help you get up and running in no time.

CPC Pump

The CPC Sanitary Centrifugal Pump is manufactured by Pomac Pumps and has been designed to EHEDG guidelines making it ideal for hygienic applications. If you’ve been having problems with your CPC Pump, try our troubleshooting guide below or if it continues, contact the team at Tapflo UK for help.

Malfunctions

What are the main causes of malfunction of the CPC Sanitary Centrifugal Pump?

A malfunction in a pump system may be caused by a number of reasons and is not necessarily the pump itself. Issues with the pipework or other fluid accessories within the system can be contributing factors. Another major contributing factor would be operating the pump in conditions that are extremely different from the ones provided at the time of specification.

Consequently, it is always recommended to check the following first:

  • Has the pump been installed correctly?
  • Are the operating conditions still according to the initial specification?
  • Are the other fluid accessories within the pipework functioning correctly?

In general, the following malfunctions can be identified:

  1. Pump provides little or no flow
  2. Pump does not reach duty point
  3. Pump provides irregular flow
  4. Pump leaks
  5. Pump vibrates excessively
  6. Pump makes too much noise
  7. Motor overheats
  8. Motor / Pump cuts out on thermal overload
  9. Pump has seized

Below is a table of the possible causes and solutions of these malfunctions.

Malfunction Cause Solution
1 2 3 4 5 6 7 8 9
  X       X X     Electrical Connection is defective Have a qualified electrician check the connections
  X               Wrong Direction or Rotation Have a qualified electrician reverse the direction of rotation of the electric motor
X                 The pump is not completely filled with liquid Fill the pump casing entirely with fluid and fit a non-return valve to the suction side
X X X     X       Insufficient Suction Pressure Increase the suction pressure or lower position of the pump further below the fluid level
  X           X   Pump operating at the wrong speed Check the motor speed
                X Contamination or objects are lodged within the pump which is larger than the solids handling capacity Clean the pump and install a suction filter if necessary
X X X             Air in the pipework Inspect the pipework and avoid upward rising bends in the pipework
  X               Valve in the suction pipework is not completely open Entirely open the valve
  X               The pump has been selected with too low a delivery pressure Install a larger pump or install a booster pump
X X X           X Suction pipe or filter is blocked Clean the suction pipe or filter
      X           Shaft Seal is defective Replace the Seal
      X           O-Ring is defective Replace the O-Ring
              X   Liquid Temperature is too high Decrease the liquid temperature
X             X X Impeller is jammed Unclog the impeller and replace if necessary
        X X   X X Impeller is damaged Replace the impeller
        X X X X X Motor Shaft is bent Replace the motor
        X X X X X Extension shaft is loose Inspect the extension shaft, reassemble and readjust
        X X X X X Bearings are damaged or worn Replace the motor, for IG(H) replace the bearings.
              X X Motor is overloaded Check the viscosity of the fluid.

Switch off the motor and check if the pump does not drag, if so, disassemble and repair.

Written by

Edward Shaw

| Technical Manager

Edward Shaw is Technical Manager at Tapflo Pumps UK, with 19 years of experience delivering technical pump solutions across the Oil & Gas, Industrial, Marine and Food & Beverage sectors. He specialises in customised pump engineering, applying in-depth process knowledge to improve efficiency, reliability, and lifecycle performance for demanding industrial applications.

SEE MORE FROM AUTHOR CONNECT ON LINKEDIN
Last updated 24/06/2026 3 minutes read

Latest Articles

aseptic EHEDG diaphragm pumps on a palette
Blog
|
4 minutes read

Diaphragm Pump Materials & Chemical Compatibility

READ MORE
A photo of Sanitary Diaphragm Pumps
Blog
|
6 minutes read

How to Choose a Diaphragm Pump: Buying Guide

READ MORE
aseptic EHEDG diaphragm pumps on a palette
Blog
|
4 minutes read

Diaphragm Pump Common Applications and Industries

READ MORE
This is a photo of bottles on a production line
Blog
|
6 minutes read

Peristaltic Pumps for Hygienic Applications

READ MORE